Examination of the Contributing Factors to Fatalities in Electrical Trades Due to Contact With Electricity.

OBJECTIVE: The aim of this study was to examine contributing factors to fatalities in electrical occupations due to contact with electricity. METHODS: Proportionate mortality ratios were calculated along with the Mantel-Haenszel chi-square test of significance using Occupational Safety and Health Administration data. Cross-tabulation analyses were examined by the Pearson chi-square test of independence. RESULTS: Electricians and electrical power installers/repairers experienced significantly higher proportions of fatalities due to contact with electric current of machine, tool, or light fixture and contact with overhead power lines, respectively. Factors such as accident date, location, union status, project type, cost, electrical event, human factor, part of body, source of injury, and fatality cause, exhibited significant associations with electrical trade fatalities. CONCLUSIONS: Fatalities in electrical occupations are attributable to increased exposures to electrical hazards during regular work activities. Strict adherence to safe work practices and procedures is critical to electrical fatality prevention.

Low-voltage electric shock - proposed new recommendations. / Strømgjennomgang fra lavspenning ­ forslag til nye anbefalinger.

We propose new recommendations for the emergency treatment of low-voltage electric injuries (<1 000 volts). A large proportion of these patients can be treated as outpatients.

Hands-on defibrillation with safety drapes: Analysis of compressions and an alternate current pathway.

BACKGROUND: Hands-on defibrillation (HOD) could theoretically improve the efficacy of cardiopulmonary resuscitation (CPR) though a few mechanisms. Polyethylene drapes could potentially facilitate safe HOD, but questions remain about the effects of CPR on polyethylene's conductance and the magnitude of current looping through rescuers' arms in contact with patients. METHODS: This study measured the leakage current through 2 mil (0.002 in.) polyethylene through two different current pathways before and after 30 min of continuous compressions on a CPR mannequin. The two pathways analyzed were the standardized IEC (International Electrotechnical Commission) leakage current analysis and a setup analyzing a current pathway looping through a rescuer's arms and returning to the patient. First, ten measurements involving the two pathways were obtained on a single polyethylene drape. 30 min of continuous compressions were applied to the drape on a CPR mannequin after which the ten measurements were repeated. RESULTS: Twenty patients undergoing elective cardioversion for atrial fibrillation (18/20) or atrial flutter (2/20) at Emory University Hospital underwent analysis all receiving 200 J shocks (age 38-101, 35% female). Through the IEC measurement method the peak leakage current mean was 0.70 +/- 0.02 mA before compressions and 0.59 +/- 0.19 mA after compressions. Only three of the ten measurements assessing current passing through a rescuer's arms had detectable current and each was of low magnitude. All measurements were well below the maximum IEC recommendations of 3.5 mA RMS and 5.0 mA peak. CONCLUSIONS: Polyethylene may facilitate safe HOD even after long durations of compressions. Current looping through a rescuer's arms is likely of insignificant magnitude.

Early intervention mechanism for preventing electrocution in construction engineering.

The aim of this study is to establish an effective early intervention mechanism for construction engineering to prevent electrocution while improving labor safety and reducing the casualty risk. This study used narrative text analysis and the Haddon Matrix for data collection, and analyzed the causes from the 113 electrocution deaths among in the construction industry, the exhaustive chi-square automatic interaction detector algorithm was employed the segmentation of the correlations. Based on the theory of inventive problem solving, through IDEF0 (ICAM DEFinition) for function modeling was designed the early intervention mechanism. This study revealed the operating features related to electric shock hazards. Early intervention was introduced to reduce the relevant risks and establish safety mechanisms. The first contribution of this study is the determination of hazard correlations between operating features and conductive media, and entry point for the prevention of electrocutions. The second contribution is the suggestion of the establishment of inspection stations for electric tools, thereby ensuring that the portable power tools are safe. The final contribution is the joint application of TRIZ (Teoriya Resheniya Izobreatatelskikh Zadatch) and IDEF0, which establishing the pre-entry testing, strengthening safety mechanisms.

Shields on Electric Posts Prevent Primate Deaths: A Case Study at Polonnaruwa, Sri Lanka.

When monkeys, such as the toque macaques (Macaca sinica) of Sri Lanka, seek food on the ground near human habitation, they may use electrical posts to escape aggression from conspecifics, dogs, or humans. Shields mounted on electrical posts prevented monkeys from reaching the electrical wires, thereby averting their electrocution: the frequency of electrocutions (n = 0) was significantly less (p < 0.001) in the 12 years after installation of the shields than in the 12 years before (n = 18). Electric shocks were either fatal (n = 14) or caused permanent injury (n = 4) (collectively referred to as electrocutions hereafter). The shields may find broader applications in other primate species and environments wherever monkeys are attracted by human food near electrical posts. Primates and other arboreal mammals also accessed live wires from trees; at known electrocution hotspots, short spans of exposed wires were insulated by encapsulating them in PVC water pipes. It was impossible, however, to prevent electrocutions from all electric supply infrastructures that put monkeys at risk. A wider use of insulated electric conductors in planning power distribution in habitats frequented by wild animals would be desirable in preventing electric shocks to wildlife.

BET 1: Can hands-on defibrillation be performed safely?

A short cut review was carried out to see whether hands-on defibrillation could be performed safely. 6 papers presented the best evidence to answer the clinical question. The author, date and country of publication, patient group studied, study type, relevant outcomes, results and study weaknesses of these papers are tabulated. It is concluded that hands-on defibrillation has the potential to be performed safely if the rescuer uses appropriate electrical insulating barriers such as polyethylene gloves or class 1 electrical insulating gloves. The safety profile of nitrile gloves is unclear. Since detection of shock was used as a proxy for safety, additional investigation is warranted before hands-on defibrillation becomes common practice.

Electrical safety.

Since the purpose of clinical neurophysiology testing is to record the electrical activity of the nervous system, and often to electrically stimulate the peripheral or central nervous system (for evoked potentials, nerve conduction studies, etc.), these tests by their very nature demand an excellent electrical connection to the patient. This direct electrical connection by definition puts the patient at increased risk of electrical shock. When patients suffer from other nonneurological disorders that also require equipment to be attached to or inserted into their body, the additional and more direct electrical pathways to the heart make them even more vulnerable, especially when undergoing monitoring in the operating room or intensive care unit. Although we depend on the hospital's construction and utilities to follow appropriate regulations (the National Electrical Code in the United States) and on the vendors to sell only safe equipment (approved by the Food and Drug Administration in the United States), there may exist combinations of equipment and connections that put the patient at risk of injurious or fatal electrical shock. Regular testing and safe practices, informed by a scientific understanding of the risks, are the responsibilities of the healthcare providers in order to protect the patient from harm from electricity.

Protocols for documentation of electrical injuries for electrical safety inspectors and emergency medical practitioners.

BACKGROUND: Electric shocks are common, and victims report difficulty in finding practitioners with knowledge of the injury. Medical Practitioners, especially in private practice, report lack of knowledge of the injury and lack of expertise in assessing and treating the injury. The authors are often requested to suggest investigation protocols, assessment protocols, and treatment protocols, and to provide educational information. METHODS: The international body establishing electrical standards on the effects of current on the body (International Electrotechnical Commission, Maintenance Team 4 (MT4) of Technical Committee 64 (TC64)) have established protocols for the factors which require documentation and reporting of the injury. This article provides a narrative approach to using these protocols in accord with the standards (IEC 60479). The level of evidence is Level III (US/Canada classification). TYPE: This article collects together and collates physical and medical aspects of investigating electric shocks, and summarizes those of importance, and which are potentially forgotten. The thoroughness of initial assessment is emphasized. SUBSTANCE: Summaries are set out to guide first attenders and emergency medical personnel as to findings and observations which must be recorded for later comprehensive medicolegal reporting and which are often overlooked. CONCLUSION: Wider teaching in the nature of electric shocks will enhance assessment of victims and thorough recording of pertinent information and thus will enhance later medicolegal reporting. Many such factors are initially overlooked and lead to inadequate reporting for forensic purposes.

Hands-on defibrillation with a safety barrier: An analysis of potential risk to rescuers.

BACKGROUND: Interruptions in compressions reducethe efficacy of cardiopulmonary resuscitation (CPR) and are inevitable during hands-off periods for shocks. Clinical exam gloves were found to facilitate safe contact with patients during shock delivery but the safety of this practice has been questioned. Polyethylene is of interest because of its safety record in the medical arena and its electrical insulation properties. METHODS: This study measured the current leak through 2 mil (0.002 inch) polyethylene drapes during shock delivery. The current leak was assessed by measurement of voltage changes in a circuit recommended by the International Electrotechnical Commission (IEC) for current leak safety testing. Current flowed off the drape, through the circuit and to electric ground in a manner consistent with standardized testing. Perceptibility was assessed in a subset with the investigator's bare hands pressed into the drape during shock delivery. RESULTS: Thirty-three patients undergoing elective cardioversion at Emory University Hospital underwent analysis (age 23-90, 36% female). Biphasic energies were 200-360 J. The root mean square (RMS) current leak averaged 0.072 ± 0.022 mA and peak current leak averaged 0.67 ± 0.21 which is well below IEC recommendations of 3.5 mA RMS and 5.0 mA peak. Finally, no instances of dielectric breakdown occurred and no shocks were perceptible. CONCLUSIONS: Polyethylene is a common medical material which may facilitate safe hands-on defibrillation. Our data illustrates that a thin, semitransparent layer of polyethylene is a safe and feasible adjunct to cardiac arrest kits to allow continued compressions and simplification of the CPR process.

[Work accidents and automatic circuit reclosers in the electricity sector: beyond the immediate causes]. / Acidentes de trabalho e os religadores automáticos no setor elétrico: para além das causas imediatas.

The Brazilian electricity sector has recorded high work-related mortality rates that have been associated with outsourcing, used to cut costs. In order to decrease the power outage time for consumers, the industry adopted the automatic circuit recloser as the technical solution. The device has hazardous implications for maintenance workers. The aim of this study was to analyze the origins and consequences of work accidents in power systems with automatic circuit recloser, using the Accident Analysis and Prevention (AAP) model. The AAP model was used to investigate two work accidents, aimed to explore the events' organizational origins. Case 1 - when changing a deenergized secondary line, a worker received a shock from the energized primary cable (13.8kV). The system reclosed three times, causing severe injury to the worker (amputation of a lower limb). Case 2 - a fatal work accident occurred during installation of a new crosshead on a partially insulated energized line. The tip of a metal cross arm section strap touched the energized secondary line and electrocuted the maintenance operator. The circuit breaker component of the automatic circuit recloser failed. The analyses revealed how business management logic can participate in the root causes of work accidents through failures in maintenance management, outsourced workforce management, and especially safety management in systems with reclosers. Decisions to adopt automation to guarantee power distribution should not overlook the risks to workers in overhead power lines or fail to acknowledge the importance of ensuring safe conditions.

O setor elétrico brasileiro registra elevados índices de mortalidade por acidentes de trabalho que vêm sendo associados à terceirização, introduzida como forma de rebaixamento de custos. Para diminuir o tempo de interrupção do fornecimento de energia aos consumidores, o setor adotou, como solução tecnológica, o religador automático. Essa medida apresenta características perversas para os trabalhadores de manutenção. O objetivo deste estudo é analisar origens e consequências de acidentes de trabalho em sistemas elétricos dotados de religador automático utilizando o Modelo de Análise e Prevenção de Acidentes (MAPA). O MAPA foi usado na investigação de dois acidentes de trabalho visando a explorar as origens organizacionais dos eventos. Caso 1 - ao trocar linha secundária desenergizada, um trabalhador foi atingido por cabo primário energizado (13,8kV). O sistema foi religado três vezes, agravando as lesões (amputação de membro inferior). Caso 2 - acidente de trabalho fatal ocorrido durante instalação de cruzeta nova, em linha energizada, parcialmente isolada. A extremidade de uma mão francesa metálica encostou na linha secundária energizada e eletrocutou o operador de manutenção. O componente desligador do religador automático não funcionou. As análises contribuem para desvelar como a lógica de gestão de negócios pode participar nas origens de acidentes de trabalho via falhas da gestão de manutenção, da gestão de força de trabalho de terceiras e, em especial, da gestão de segurança em sistemas dotados de religadores. As decisões pela automação para garantir a distribuição de energia não podem negligenciar os riscos aos trabalhadores da rede elétrica e, tampouco, deixar de reconhecer a importância do controle sobre as condições de segurança.

El sector eléctrico brasileño registra elevados índices de mortalidad por accidentes de trabajo, que están siendo asociados a la tercerización, introducida como forma de reducción de costes. Para disminuir el tiempo de interrupción de la energía a los consumidores, el sector adoptó como solución tecnológica, el reconectador automático. Esta medida presenta características perversas para los trabajadores del sector de mantenimiento. El objetivo de este estudio es analizar los orígenes y consecuencias de los accidentes de trabajo en sistemas eléctricos dotados de reconectador automático, utilizando el Modelo de Análisis y Prevención de Accidentes (MAPA). El MAPA se usó en la investigación de dos accidentes de trabajo, con el objetivo de explorar las causas organizativas de los eventos. Caso 1 - al cambiar la línea secundaria sin energía, un trabajador fue alcanzado por un cable primario con energía (13,8kV). El sistema se reconectó tres veces, agravando las lesiones (amputación de miembro inferior). Caso 2 - accidente de trabajo fatal ocurrido durante la instalación de una cruceta nueva, en una línea con energía, parcialmente aislada. La extremidad de una cruceta metálica cayó en la línea secundaria con energía y electrocutó al obrero de mantenimiento. El componente que desconectaba el reconectador automático no funcionó. Los análisis contribuyen a desvelar cómo la lógica de gestión de negocios puede ser partícipe en las causas de accidentes de trabajo, vía fallos en la gestión del mantenimiento, de la gestión de fuerza de trabajo de terceras personas y, en especial, de la gestión de seguridad en sistemas dotados de reconectadores. Las decisiones de la automatización para garantizar la distribución de energía no pueden obviar los riesgos para los trabajadores de la red eléctrica y tampoco dejar de reconocer la importancia del control sobre las condiciones de seguridad.

Acidentes de trabalho e os religadores automáticos no setor elétrico: para além das causas imediatas / Work accidents and automatic circuit reclosers in the electricity sector: beyond the immediate causes / Accidentes de trabajo y reconectadores automáticos en el sector eléctrico: más allá de las causas inmediatas

Resumo: O setor elétrico brasileiro registra elevados índices de mortalidade por acidentes de trabalho que vêm sendo associados à terceirização, introduzida como forma de rebaixamento de custos. Para diminuir o tempo de interrupção do fornecimento de energia aos consumidores, o setor adotou, como solução tecnológica, o religador automático. Essa medida apresenta características perversas para os trabalhadores de manutenção. O objetivo deste estudo é analisar origens e consequências de acidentes de trabalho em sistemas elétricos dotados de religador automático utilizando o Modelo de Análise e Prevenção de Acidentes (MAPA). O MAPA foi usado na investigação de dois acidentes de trabalho visando a explorar as origens organizacionais dos eventos. Caso 1 - ao trocar linha secundária desenergizada, um trabalhador foi atingido por cabo primário energizado (13,8kV). O sistema foi religado três vezes, agravando as lesões (amputação de membro inferior). Caso 2 - acidente de trabalho fatal ocorrido durante instalação de cruzeta nova, em linha energizada, parcialmente isolada. A extremidade de uma mão francesa metálica encostou na linha secundária energizada e eletrocutou o operador de manutenção. O componente desligador do religador automático não funcionou. As análises contribuem para desvelar como a lógica de gestão de negócios pode participar nas origens de acidentes de trabalho via falhas da gestão de manutenção, da gestão de força de trabalho de terceiras e, em especial, da gestão de segurança em sistemas dotados de religadores. As decisões pela automação para garantir a distribuição de energia não podem negligenciar os riscos aos trabalhadores da rede elétrica e, tampouco, deixar de reconhecer a importância do controle sobre as condições de segurança.

Abstract: The Brazilian electricity sector has recorded high work-related mortality rates that have been associated with outsourcing, used to cut costs. In order to decrease the power outage time for consumers, the industry adopted the automatic circuit recloser as the technical solution. The device has hazardous implications for maintenance workers. The aim of this study was to analyze the origins and consequences of work accidents in power systems with automatic circuit recloser, using the Accident Analysis and Prevention (AAP) model. The AAP model was used to investigate two work accidents, aimed to explore the events' organizational origins. Case 1 - when changing a deenergized secondary line, a worker received a shock from the energized primary cable (13.8kV). The system reclosed three times, causing severe injury to the worker (amputation of a lower limb). Case 2 - a fatal work accident occurred during installation of a new crosshead on a partially insulated energized line. The tip of a metal cross arm section strap touched the energized secondary line and electrocuted the maintenance operator. The circuit breaker component of the automatic circuit recloser failed. The analyses revealed how business management logic can participate in the root causes of work accidents through failures in maintenance management, outsourced workforce management, and especially safety management in systems with reclosers. Decisions to adopt automation to guarantee power distribution should not overlook the risks to workers in overhead power lines or fail to acknowledge the importance of ensuring safe conditions.

Resumen: El sector eléctrico brasileño registra elevados índices de mortalidad por accidentes de trabajo, que están siendo asociados a la tercerización, introducida como forma de reducción de costes. Para disminuir el tiempo de interrupción de la energía a los consumidores, el sector adoptó como solución tecnológica, el reconectador automático. Esta medida presenta características perversas para los trabajadores del sector de mantenimiento. El objetivo de este estudio es analizar los orígenes y consecuencias de los accidentes de trabajo en sistemas eléctricos dotados de reconectador automático, utilizando el Modelo de Análisis y Prevención de Accidentes (MAPA). El MAPA se usó en la investigación de dos accidentes de trabajo, con el objetivo de explorar las causas organizativas de los eventos. Caso 1 - al cambiar la línea secundaria sin energía, un trabajador fue alcanzado por un cable primario con energía (13,8kV). El sistema se reconectó tres veces, agravando las lesiones (amputación de miembro inferior). Caso 2 - accidente de trabajo fatal ocurrido durante la instalación de una cruceta nueva, en una línea con energía, parcialmente aislada. La extremidad de una cruceta metálica cayó en la línea secundaria con energía y electrocutó al obrero de mantenimiento. El componente que desconectaba el reconectador automático no funcionó. Los análisis contribuyen a desvelar cómo la lógica de gestión de negocios puede ser partícipe en las causas de accidentes de trabajo, vía fallos en la gestión del mantenimiento, de la gestión de fuerza de trabajo de terceras personas y, en especial, de la gestión de seguridad en sistemas dotados de reconectadores. Las decisiones de la automatización para garantizar la distribución de energía no pueden obviar los riesgos para los trabajadores de la red eléctrica y tampoco dejar de reconocer la importancia del control sobre las condiciones de seguridad.

Erroneous Magnet Positioning Leads to Failure of Inhibition of Inappropriate Shock during Fast Conducting Atrial Fibrillation Episodes.

We present the case of a 75-year-old patient with a single-chamber St. Jude Medical internal cardioverter defibrillator (ICD; St. Jude Medical, St. Paul, MN, USA) for primary prevention, who was admitted with 39 inappropriate ICD shocks because of atrial fibrillation with rapid ventricular frequention, despite magnet placement. Review of the device manual and literature revealed that apart from different responses to magnet placement programmed for the various manufacturers, the type of magnet and the positioning can be of specific interest. In the case presented, the donut-shaped magnet should have been placed off-center instead of directly over the device.

Longitudinal changes in quality of life following ICD implant and the impact of age, gender, and ICD shocks: observations from the INTRINSIC RV trial.

PURPOSE: ICDs can improve survival in at-risk patients but no consensus exists with respect to their impact on health-related quality of life (QOL). Moreover, the data are unclear on QOL benefits in specific patient subgroups. We sought to analyze, in the INTRINSIC RV ICD trial population, health-related QOL longitudinally following ICD implant and consider impact of age, gender, and ICD shocks on QOL by employing a global measure of health-related QOL. METHODS: One thousand five hundred thirty patients had an ICD implanted. One week after implant (n = 1461), 988 patients were randomized to DDDR with AV search hysteresis (n = 502) or VVI (n = 486) programming. QOL data, using the SF-36 short form, were obtained for the 1461 patient cohort, irrespective of randomization status, at baseline and prospectively for 1 year following ICD implant. RESULTS: Longitudinal mixed-effect analyses revealed significant improvements from baseline across all SF-36 subscales and component scores for the overall study cohort. Women had a substantially lower QOL at baseline, although their improvement after implant was similar to men. Patients <50 years scored consistently worse at baseline but experienced the greatest QOL improvement versus other age groups. Patients with higher NYHA class, angina, and diabetes had greater QOL improvements. There was no significant difference in QOL between patients with and without ICD shocks. CONCLUSIONS: Our findings indicate that QOL was reportedly better post-implant and suggest that benefits associated with ICD implantation go beyond the direct treatment of arrhythmias, with benefits seen across genders and different age groups. These results further highlight that ICD implantation, in and of itself, does not reduce QOL.

The Design of the Understanding Outcomes with the S-ICD in Primary Prevention Patients with Low EF Study (UNTOUCHED).

BACKGROUND: The UNTOUCHED study will assess the safety and efficacy of the subcutaneous implantable cardioverter defibrillator (S-ICD) in the most common cohort of patients receiving ICDs. The primary goal is to evaluate the inappropriate shock (IAS)-free rate in primary prevention patients with a reduced ejection fraction (EF) and compare with a historical control of transvenous ICD patients with similar programming. METHODS AND RESULTS: The UNTOUCHED study is a global, multicenter, prospective, nonrandomized study of patients undergoing de novo S-ICD implantation for primary prevention of sudden cardiac death with a left ventricular EF ≤35%. The primary end point of this trial is freedom from IAS at 18 months. The lower 95% confidence bound of the observed incidence will be compared to a performance goal of 91.6%, which was derived from the IAS rate in MADIT-RIT. The secondary end points are all-cause shock-free rate at 18 months, and system- and procedure-related complication-free rate at 1 month and 6 months. Enrollment of a minimum of 1,100 subjects from up to 200 centers worldwide is planned based on power calculations of the primary and principal secondary end points. CONCLUSIONS: This trial will provide important data regarding the rates of inappropriate and appropriate shock therapy in real-world use of the S-ICD in the most common group of patients receiving ICDs.

"Spontaneous Twiddler's" Syndrome: The Importance of the Device Shape.

Twiddler's syndrome is caused by patient manipulation of the cardiac implantable device (CID) around its central axis within the pocket, resulting in retraction and dislocation of the electrodes. There are, however, some reports that Twiddler's syndrome may occur spontaneously without the patient's manipulation. This remains contentious as it may be argued that patients may not want to admit to manipulating the CID or may have been unaware of their actions. Recently, we have observed three very similar cases with a "spontaneous" Twiddler's syndrome resulting in lead displacement. All of the three patients denied device manipulation and were not prone to somnambulism or repetitive involuntary motor behaviors. It, therefore, seems highly unlikely that all patients could have manipulated the device in exactly the same way to result in the same postrotational position within the implant pocket. The fact is that the same device was implicated in all these cases in a relatively similar time sequence from implant to recognition of the implantable cardiac defibrillator rotation. We postulate that the unique elongated decision of the Fortify Assura (St. Jude Medical, Minneapolis, MN, USA) ICD makes this device prone to spontaneous rotation as is exemplified by our case series.

Is modification of the VVI backup mode in implantable cardioverter-defibrillators from St Jude medical required due to increased risk of inappropriate shocks?

Inappropriate implantable cardioverter-defibrillator (ICD) shock therapy is painful, stressful, and typically occurs unexpected in conscious patients and may be related to a less favourable prognosis. In our institution, we have observed four cases of multiple inappropriate ICD shocks during reset to VVI backup mode. All four patients were implanted with a St Jude Medical ICD since 2010. The reset to VVI backup mode happens as a 'safety' response when the ICD encounters errors in the software or hardware often due to electromagnetic interference. The ICD then operates in a simple mode, with only a ventricular fibrillation (VF) zone starting at 146 b.p.m., with shock therapy only and changes in sensitivity settings making the ICD more sensitive. In all cases, the reason for the multiple inappropriate shocks was that the VF zone was reached due to exercise-induced sinus tachycardia or due to oversensing during sinus rhythm. The VVI backup mode has to balance between protection from failure of ICD therapy during life-threatening ventricular arrhythmias and from inappropriate shocks. It seems the non-programmable parameters in VVI backup mode of St Jude Medical ICDs carry an unacceptable high risk of inappropriate shocks during normal rhythm as illustrated by our four cases. A higher VF zone comparable with the zones chosen by the other manufacturer would give a better balance, since it is very unlikely that a patient will need shock therapy urgently for slow ventricular tachycardia.

Identify, Verify, and Comply: The Three Pillars of a Successful Electrical Safety Program.

What's shocking is that many workers are not using rubber insulating equipment because they simply don't know they need it.

[Optimisation of subcutaneous defibrillator programming after inappropriate shocks due to new onset of right bundle branch block]. / Optimierung der Geräteeinstellung eines subkutanen Defibrillators nach inadäquaten Schocks durch neu aufgetretenen Rechtsschenkelblock.

The subcutaneous implantable defibrillator (S-ICD) has become an established tool for the prevention of sudden cardiac death. Based on its detection properties, the S­ICD is essentially dependent on correct morphology discrimination of the QRS complex and avoidance of potential T­wave sensing. We report on a patient who experienced multiple inappropriate S­ICD shocks due to T­wave oversensing in the setting of new onset of right bundle branch block. Strategies for the optimisation of the device programming are discussed.